Learn how to start car when battery is low: A car that has low battery could lead to a lot of stress; it could lead to inconvenient times. It is important to know that how to handle this situation, as it would lead to free from those inconvenient times. This article will help to delve into the different nuances of the topic on how to start car when battery is low.
Step -by-Step Guide to starting a car with a low battery
A) Jump Start the Car
If a car has low battery, then jump starting the car is one of the common methods to revive the car. In jump starting the car only two tools are needed, those are- Jumper cables and another car that is fully charged battery.
Steps:
- a) Align the Vehicles: The donor vehicle should be positioned so that the jumper wires can readily reach both batteries and that it does not come into contact with the other vehicle. It should also be close enough to the vehicle to ensure this.
- b) Switch off Both Vehicles: It’s crucial to switch off both vehicles before attaching the cords.
- c) Connect Jumper Cables: A jumper cable has two points: a red cable and a black cable. The positive segment (+) of the dead battery should be connected to one end of the red cable, and the positive segment (+) of the donor battery should be connected to the other. A black cable’s one end needs to be connected to the donor battery’s negative segment (-). The engine block of the deceased car should have the other end fastened to an unpainted metal surface.
- d) Turn on the Donor automobile: In order to recharge the dead battery, the donor automobile needs to be turned on for a few minutes.
- e) Start the Dead Car: Make an attempt to start the vehicle with the dead battery. Allow it to run for a few minutes if it can start.
- f) Disconnect Cables: In order to disconnect the cables, they must be done so in reverse order, which is black to red.
- g) Continue to Run the Engine: The car needs to be driven for at least 20 minutes to recharge the dead battery after it has been revived.
B) Push Start (Manual Transmission Only)
In the manual transmission of the cars, push start method can be used.
Steps:
- a) Find a Slope or Get Help: In the case of a slope the car should be position in a down facing way or if there is no slope could be found than one should get help from someone to help in push the car.
- b) Turn the Ignition On: The key of the car must be in a on position.
- c) Put the Car in the Second Gear: The gear of the car should be in the second, to do this the clutch needs to be press and the gear needs to be shifted.
- d) Release the Brake and Start Moving: Slowly let go of the brake while someone pushes the car from behind or if there is slope it could roll down of the slope.
- e) Release the Clutch Quickly: Once the car is able to gain some speed, quickly release the clutch to engage the engine. The car should start.
C) Use a Battery Charger
If there is an availability of battery charger, the car could be easily be charged without the need for another vehicle.
Steps:
- a) Remove the Battery: The battery needs to be disconnected from the car.
- b) Connect the Charger: The red clamp that is the positive end of the charger to battery’s positive terminal and the negative end that is the black clamp to the negative terminal.
- c) Set the Charger: It is very important to select the appropriate voltage and amperage settings on the charger.
- d) Charge the Battery: The charger needs to be plug in as to let to get charged until the battery is fully charged, it takes about several hours.
- e) Reinstall the Battery: Once the battery is fully charged, the charger is disconnected and then the battery is reinstalled again in the car.
Frequently Asked Questions
There are several signs that includes the headlights of the car will be dim, there will be slow engine clank, there will be clicking sound while turning on the key, and the dashboard will show warning signs.
The car should be run for almost 20 minutes as it will allow the alternator to charge the battery fully.
If a car has low battery, then will put an extra strain on the alternator and it could damage it very badly. Therefore, it is important to address the battery issues as early as possible.
Conclusion
A car with a low battery can cause stress and inconvenience. To revive a car, jump start is a common method, requiring jumper cables and a fully charged battery. The donor vehicle should be positioned so that the jumper wires can reach both batteries without contact. Switch off both vehicles before attaching the cords. Connect jumper cables to the donor battery’s positive and negative segments. Turn on the donor car, start the dead car, disconnect cables, and continue to run the engine. For manual transmission cars, push start can be used. Find a slope or get help, turn ignition on, put the car in the second gear, release the brake, and start moving. Release the clutch quickly to engage the engine. If a battery charger is available, charge the battery without another vehicle. Remove the battery, connect the charger, set the charger, charge the battery, and reinstall the battery. This process takes several hours and ensures the car is fully charged before disconnecting the charger and reinstalling the battery.
[…] Also Read: How to Start Car When Battery is Low? […]